کابل مبدل USB به سریال TTL مدل PL2303TA
کابل های سریال USB به TTL به شما امکان می دهد به پورت کنسول سریال Raspberry Pi یا میکروکنترلر متصل شوید.
بدنه اصلی دارای یک تراشه تبدیل سریال USB است و انتهای دیگر دارای چهار سیم برای اتصال به برد مورد نظر شما است:
قرمز = پاور
سیاه = اتصال به زمین
سفید = RX (به درگاه USB)
سبز = TX (خارج از پورت USB)
پایه پاور 5 ولت 500 میلی آمپر را مستقیماً از درگاه USB فراهم می کند و پایه های RX/TX 3.3 ولت برای رابط با اکثر چیپست های معمولی سطح منطقی 3.3 ولت هستند.
سیم های جامپر تقسیم شده اتصال به کنسول اشکال زدایی Raspberry Pi را آسان می کند. فقط سیم ها را به پین های صحیح وصل کنید تا پیوندی به برد خود تنظیم کنید. حتی می توانید از این کابل ها در برخی از روترهای WiFi برای نصب سیستم عامل های جایگزین استفاده کنید.
این کابل برای برنامه نویسی مجدد آردوینو نیست – سیم DTR/RTS لازم برای شروع دنباله راه اندازی مجدد بوت لودر را ندارد. به جای آن از FTDI استفاده کنید.
اگر لینوکس را اجرا می کنید، درایورها از قبل در هسته گنجانده شده است، نیازی به نصب چیزی نیست!
USB to Serial TTL Converter – 5V Supply 3.3V IO
This USB to serial (TTL) converter makes it easy to program Arduino or any embedded device. The convert use the PL2303 chipset that comes standard with most Windows and Linux operating systems.
Features:
This is a newly designed product, using the Taiwan prolific production company PL2303TA chips, PL2303TA perfectly compatible with win XP/VISTA/7/8/8.1 system
PL2303TA provides a convenient solution for connecting an RS232-like full-duplex asynchronous serial device to any Universal Serial Bus (USB) capable host. PL2303TA highly compatible drivers could simulate the traditional COM port on most operating systems allowing the existing applications based on COM port to easily migrate and be made USB ready without having to rewrite the COM port software application.
By taking advantage of USB bulk transfer mode, large data buffers, and automatic flow control, PL2303TA is capable of achieving higher throughput compared to traditional UART (Universal Asynchronous Receiver Transmitter) ports.When real RS232 signaling is not required, baud rate higher than 115200 bps could be used for even higher performance. The flexible baud rate generator of PL2303TA could be programmed to generate any rate between 75 bps and 6M bps.
PL2303TA is exclusively designed for mobile and embedded solutions in mind, providing a small footprint that could easily fit in to any connectors and handheld devices. With very small power consumption in either operating or suspend mode, PL2303TA is perfect for bus powered operation with plenty of power left for the attached devices. Flexible signal level requirement on the RS232-like serial port side also allows PL2303TA to connect directly to any 3.3V~1.8V range devices.
This product is designed for laboratory, product testing, low-cost MCU communications and other applications, there are four lead,
Quick Spec
- Chipset: PL2303
- Connector: USB Type-A plug, 4-pin 2.54mm pinheader
- Length: 1m
Red +5 V
Black GND
White RXD
Green TXD
Product Applications:
- Single-chip upgrade solution for Legacy RS232 devices to USB interface
- USB to RS232 converters/cables/dongles
- Healthcare/Medical USB Interface Data Transfer Cable
- Personal Infotainment/Media Player Docking USB Interface
- Cellular/PDA USB Interface Data Transfer Cable
- Serial-over-IP Wireless Solution
- USB Barcode/Smart Card Readers
- GPS/Navigation USB Interface
- Point-of-Sale (POS) Terminals/Printers
- PC Docking Station/Port Replicators
- Industrial/Instrumentation/Automation Control USB Interface
- USB Modem/Wireless/Zigbee USB Interface
- Set-Top Box (STB) / Home Gateway USB Interface
- BatteryCharger Application
- MCU-based devices to USB interface
Pinouts
- Red – VCC (5V)
- Black – GND
- Green – TXD – (3.3V TTL, connects to target RXD)
- White – RXD – (3.3V TTL, connects to target TXD)
Shipping List
- 1 x USB to TTL 4-pin Wire
نقد و بررسیها0
هنوز بررسیای ثبت نشده است.